BEIYANG BTP-2200E USB DRIVER

Serial interface and Parallel interface are standard interfaces of printer, RS interface is standard Serial interface, Centronics parallel interface accords with IEEE It is the first time to mount and use the printer; The printer is used again after a long idle time; Replace new type of paper roll; First time to use it after cleaning the sensor; Fails to identify marks in effect during the print; Operation environment of the printer is changed greatly. Figure G shows the tear-off position upwards, which should be adjusted in negative direction; Figure H shows the tear-off position downwards, which should be adjusted in positive direction; 4 Routine maintenance of the printer Follow the steps as below to clean the THP, platen and sensor monthly. Paper Feed after entering the simple mode. Reduce the print darkness Please improve ventilation condition. If the operation environment is bad, you can increase routine maintenance times for the printer.

Uploader: Gozahn
Date Added: 18 February 2013
File Size: 49.50 Mb
Operating Systems: Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X
Downloads: 4344
Price: Free* [*Free Regsitration Required]

Please confirm if loaded paper is same with the one selected in the printer properties. If the printer is idle for a long period, please disconnect the power.

Must comply with warning to avoid bodily harm or damage to device Notice: Error LED status Two flashes Reasons THP is lifted up Micro-switch fault Paper roll is end or no paper roll is loaded Paper jam Paper roll surface is dirty or damaged Settlement Please press down the THP Beiyxng with maintenance people Load paper roll Remove paper jam Please cross over dirty or damaged part Load paper roll again Clean marked paper sensor surface Set paper type in the printer driver is same with actual paper type Make communication cable connection firmly Set the communication interface of the print consisting with that of PC Such as: If this THP still fail to work properly, please contact with our distributor or manufacture.

Only when the printer checkout is correct, it can work normally. To select thermal transfer mode, you need to mount ribbon; To select thermal ub, no need to mount ribbon; In normal condition, ribbon width should be bigger than the paper width; During this mount, the ribbon should not be cockled or damaged.

You may also need:  PHILIPS 170C DOWNLOAD DRIVERS

Safety instruction Before installing and using the printer, please read the following items carefully. If users need uxb further data about these products, please feel free to contact our market department or your local distributor. Trademark Our registered trademark Safety warning Caution: The btp-220e finds out USB device drive path btp-220e0 installs this driver depending on this guide.

Reduce the print darkness Please improve ventilation condition.

BTPE E USER MANUAL V1 0_百度文库

When the printer identifies that Auto checkout is needed, the printer shall feed two or three labels for checkout. The printer shall restart Auto checkout. Adjust the printout in horizontal direction with 8 dots as a motion unit. Paper type in the driver Continuous paper Black mark beiyanng Actual paper type Continuous strip paper Non-continuous marked paper Non-continuous Perforated paper Non-continuous edge-gap paper Non-continuous label paper Table 2.

It can apply to real-time label printing, label batch printing, transport and commercial label printing, other receipt printing for railway, airport, bus station, etc. This will help to keep the THP gtp-2200e. When paper roll ID is different, the loading method of paper holder into paper room will be different. Serial interface and Parallel interface are standard interfaces of printer, RS interface is standard Serial interface, Centronics parallel interface accords with IEEE User can also choose USB interface to belyang Parallel interface.

Drop paper roll on the paper holder to the paper room, then pull out the front end of the paper and put it in the print path flatly, and also release the paper guide to hold it. Paper Feed after entering the simple mode.

Print pattern hall not move when it is less than 4 dots, or the print pattern shall move based on 8 dots when it is between 4 dots and 8 dots.

You may also need:  TP-LINK TL-WN322G DRIVER

When using it, ensure that up and down time of host signal is less than 0. Please refer to 2. The quality control system of SNBC has been approved of the following certification.

BTP-2200E Barcode printer,Direct thermal, 203dpi,Free shipping

When turning the knob in clockwise, the THP pressure increases along with level number. Top cover of sensor Figure 3. Different compounding of the three LEDs means hsb setting.

If the print just finishes, you should wait for the platen cool down completely; 3 4 Clean away dusts or dirt on the transmission sensor with alcohol tampon should twisted ; Wait for 5 to 10 minutes until alcohol volatilizes completely, then press down ribbon holder and close top cover. Power LED always light.

SNBC BTPE BPLE Printer Drivers – Download Device Drivers – –

The printout is not clear; Noise in paper feed or retraction is much; Dusts stick on the platen. Check the THP test page is Normal until its temperature is down. A Transmission sensor 1 2 3 4 Turn off the printer and open top cover; Lift up the print mechanism hsb press on the latch to open the paper-pressing module; Clean away dusts or dirt on the transmission sensor with alcohol tampon should twisted ; Wait for 5 to 10 minutes until alcohol volatilizes completely, then press down ribbon holder and close top cover.

B Auto Checkout functions Before starting the print job, the printer shall compare the parameter set by customers with current parameter of the printer to decide if it shall initiate the checkout with the process as below: If the operation environment is bad, you can increase routine maintenance times for beiyzng printer.